Rolston-Smith | ESPN.com| The front porch stairs are the first step to getting your home up to code.
If you want to get that new kitchen in, you need to fix those stairs.
So what you need is some help with the stairs.
The stairs are typically made of plastic and metal, but if you want a better fit, you can always install metal brackets to the sides and rear of the stairs to help the metal stay in place.
But even if you can’t, you might be able to get the stairs fixed with a bit of help.
Here’s what you’ll need to know: Step 1: Check for damage to the stairs If you’ve installed the stairs, you’ll probably notice a lot of damage.
This is because the metal is bolted together on the outside and you can see the bolts coming off the underside of the plastic.
But if you’ve done the steps correctly, the bolts will not come off the bottom of the steps.
Step 2: Check the underside for damage There are a few different types of damage that can occur when you install stairs: The metal bolts can come loose from the sides of the door.
This usually happens when the door is opened to the inside and the metal bolts are not properly attached.
The bolt is bent out of place, like when the bolt is tightened and loosened.
This can happen when the metal has been pushed up into the door and the door hasn’t been closed properly.
In the picture above, you see the bent bolt in the rear of this door.
If the bolt comes loose, it can cause a problem with the door itself.
If this happens, you may need to replace the door to get it back in place and to keep the metal from coming loose again.
Step 3: Inspect the inside of the stairwell to see if it’s in good shape This is where you need help with your first steps.
You want to make sure the inside is clean and tight and that it’s secure.
If it’s too loose, you won’t be able keep the door closed properly, and if it has a problem, you will need to remove it.
If there are problems with the hinges, you’re likely to have to re-adjust the hinges and install new hinges.
If these problems are obvious, you should also contact the builder to discuss the steps you can take.
If they’re not visible, you probably have a few more steps to go before you get the front porch doors installed.
Step 4: Install the new hinges In most cases, the hinges will be the same as the bolts.
However, if you need the hinges to be larger or more robust, you could add a metal plate or metal tabs to the underside.
If your door is a wood-frame house, you want the metal plates or tabs to be the larger size and the larger of the two metal tabs will be bolted to the bottom.
To do this, you drill two holes in the bottom and one on the inside.
You’ll also need to drill two bolts that will go through the metal tabs and into the metal plate.
Next, you put the metal and metal plates into place.
This will keep the hinges from coming off.
To make sure everything’s in place, you pull the door up and open the hinges.
Now you have to get your new hinges in place first.
You can either install them on the top or the bottom, and you’ll have to cut them down the center to fit inside the door, but you can put them on top of the hinges as well.
Step 5: Install new metal brackets and a metal tab It’s important to have all of the metal brackets in place before you install the metal tab, because the hinges don’t need to come off without it.
To install the brackets, you first need to put the two tabs on the metal.
To ensure the tabs stay in, they’ll slide up and down inside the doors to keep them in place until you’ve finished the hinges with the metal bracket.
The metal tabs are attached to the top of a metal bracket by a plastic clip that is held to the side of the brackets.
You then attach the metal clips to the metal brace, and then attach a metal ring to the clip.
This allows the metal braces to slide up to the back of the doors and down to the front, keeping them in the same place.
To check the bolts, you place a sharp knife on the bolts and make sure they are tight.
You should then check the brackets to make them look good.
You could then tighten the brackets and make them tighten down, or you can simply remove the clips and put them back on.
You may need more time to do this to make the brackets look good, but once they’re in place you’ll be able take them off and reattach them to the hinges without worrying about the brackets falling off.
If everything is working properly, you don’t have to worry about